BOND
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A decaying structure shaping the surface – structured and yet able to leave the room calm.
FRESCOLORI® Bond
Material: 1 CM7 layer
1 CM1 layer
Consumption: CM7 about 1.2 kg/m² each layer
CM7F about 0.3 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, sturdy, in the structural direction
- Observe the quite short waiting time (surface drying)
- Smooth the surface with a trowel
BOTTOM
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A wall surface paved on a structure, but still preserving its fine radiation – structured, receding, natural.
FRESCOLORI® Bottom
Material: 1 CM7 layer
1 CM3 layer
Consumption: CM7 about 1.2 kg/m² each layer
CM0 about 0.6 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 3, in tighter execution in all directions
CONCRETE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Concrete-like surface design, with a tension which results from the interplay between the smooth properties of the material, and its structured, dense and porous radiation. A timeless modern wall design, which can vary depending on the execution, in producing its smooth, structured and thus massive and stable effect.
FRESCOLORI® Concrete
Material: 2 CM5K layers
ETC, if needed
Consumption: CM5K about 2.4 kg/m² each layer
ETC about 150 ml/m², if needed
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, with added marble granules
- Respect the waiting times with a rest period until the next day
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, with blended marble granules
- Carry out direct structuring during application
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Design freedom: light or strong smoothing of the surface
- If necessary, re-soak the excess of limestone milk after drying, with the brush (surface should be smoother after drying.)
- Protect with ETC, if necessary
CONCRETE FIVE S
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Concrete Five S, an extension of our concrete surface, obtained by adding additional coarse marble granules. A spatial experience of the concrete surface. The tensioned interaction of the opposites – cold and warm, smooth and structured, dense and porous. An individual statement, a space statement: timeless modernity, solid and stable. An effect that cannot be more immediate that now.
FRESCOLORI® Concrete Five S (sanded)
Material: 2 CM5K layers
ETC
Consumption: CM5K about 2.4 kg/m² each layer
ETC, about 0.08kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, with added coarse marble granules
- Respect the waiting times with a rest period until the next day
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, with added coarse marble granules
- Direct structuring during application, alternatively with the aid of easy application of the material
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Respect a waiting time of one day (until the next day)
- Polish the surface with the polishing machine (grain size 180)
- Apply the ETC protection with a brush
CROCO
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Croco – Wild! A surface that could make the viewer think of the skin of a crocodile. Naturally wild and fascinating beautiful – simply different.
FRESCOLORI® Croco
Material: 1 CM7 layer
1 CM1 layer
Consumption: CM7 about 1.2 kg/m² each layer
CM1 about 0.4 kg/m² each layer
Colour: freely selectable
Application: Indoor
Oberflächen sind vorbereitet und grundiert.
- Auftragen der ersten Lage des CARAMOR®-Kalkmarmorputzes in Kornstärke 7
- sofortige senkrechte oder waagerechte Aufrippung der Oberfläche mit dicken Kanten
- Einhalten Wartezeit bis zum nächsten Tag
- Aufragen der zweiten Lage des CARAMOR®-Kalkmarmorputzes in Kornstärke 1 in Ripprichtung
- Einhalten kurzer Warteizeit (handtrocken)
- Oberfläche mit der Kelle in und gegen die Ripprichtung polieren
Dragged
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
One of our massive surfaces. Raised, smoothly plastered surfaces arranged closely, in contrast, to deeper, uneven surfaces.
FRESCOLORI® Dragged
Material: 2 CM7 layer
Consumption: CM7 about 2.4 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Immediate structuring of the second layer with the structure roll
- Twice smoothing of surface, easily, with the trowel, in the drying phase
EARTH
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Fine Caramor limestone marble finds here its liveliness – larger raised smoothly plastered surfaces contrast uneven deep surfaces. Like a hidden treasure, the delicately shimmering little golden highlights appear.
FRESCOLORI® Earth
Material: 2 CM1G layers
Consumption: CM1G about 1.2 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, with added mica in full surface contact
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, in full surface contact
- Pulling the material upwards (suction effect)
- Scratching the surface with mica
- Execute a double smoothing of the surface in the drying phase, with the trowel, without water
- Respect the waiting times with a rest period until the next day
- Polishing (grain size 1000)
ELEGANT
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A wall surface with evenly smooth radiance – natural open-pore structure.
FRESCOLORI® Elegant
Material: 2 CM5 layers
Consumption: CM5 about 1.8 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 5
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 5
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Smoothing the surface
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water
FLOW
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Flow – everything is in the flow. Try CARAMOR® limestone-marble plaster once in a quite differently way. Hand-drawn longitudinal lines characterize the appearance of this matt surface and give it a harmonious appearance. It combines vitality and tranquillity in a coherent manner.
FRESCOLORI® Flow
Material: 2 CM1.5 layers
Consumption: 1. CM1,5 layer, about 0.4 kg/m²
2. CM 1.5 layer, about 1.00 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 1.5, coverage application
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 1.5, thick and textured with wallpaper wipers
- Observe the quite short waiting time (surface drying)
GRAINED
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A wall surface with evenly smooth radiance – natural open-pore structure, accentuated with coloured marble powder. The soaped surface provides an easy protection of the surface.
FRESCOLORI® Grained
Material: 2 CM5F layers
Soap
Consumption: CM5 about 2.0 kg/m² each layer
Soap, about 0.06 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the Caramor limestone-marble plaster, in grain thickness 5, with added coloured marble
- Observe the waiting times, with a rest period until the first layer is dry.
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, with coloured marble
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Design freedom: light or strong smoothing of the surface
- Observe the uniform distribution of the effluent limestone milk
- Respect the waiting times with a rest period until the next day
- With a polishing machine (grain size 180)
- Apply the soap with a brush
- Peel off the surface with a trowel
- Observe the waiting time of 2 hours
- Repeat application of the soap with a brush
- Polish the surface with a polishing machine, provided with a lambskin covered disc, and sand after a waiting period of approx. 3 hours
MARANZO® preparation
Adhesion and primer dispersion for soil
Primer, adhesive bridge and pore closure with water-repellent effect prevent the rising of air bubbles from the substrate when applying the coats. Install stainless steel termination rails with a special adhesive and separately reinforce the inner edge.
Floor levelling filler
Inside/Outside. Floor. Application of the filler, levelling and smoothing the floor surfaces made of concrete, cement screeds, tiles and paving, as well as of other suitable substrates.
Adhesion and primer dispersion for soil
Primer, adhesive bridge and pore closure with water-repellent effect prevent the rising of air bubbles from the substrate when applying the coats.
FRESCOLORI® Maranzo shower preparation
Adhesion and primer dispersion for soil
Primer, adhesive bridge and pore closure with water-repellent effect prevent the rising of air bubbles from the substrate when applying the coats. Make the slope for the shower floor.
Adhesion and primer dispersion for soil
Primer, adhesive bridge and pore closure with water-repellent effect prevent the rising of air bubbles from the substrate when applying the coats.
Reinforce and seal the floor surfaces with sealing compound
Apply two spatula spreads with a smoothing consistency, with a dry film thickness of at least 2 mm. Apply the sealing compound with the notched trowel, embed in a fabric towel, and press it using a spatula. After drying, retouch the surface a second time with the sealing compound.
FRESCOLORI® smoothing of the pre-applied layer of plaster (EP)
FRESCOLORI® Maranzo design
If needed:
FRESCOLORI® Pre-plaster levelling EP
FRESCOLORI® Maranzo EP onto the prepared floor surfaces marble plaster. After drying, apply an intermediate coat of EP primer. After renewed drying, apply the next layer and shape.
With the Maranzo surface, waves and slight differences in colour tone are the hallmark and idea; these are part of the appearance of the floor. A special feature of the technique is that the surface does not always have the same structure. Deviations from the sample surface are possible and the respective “handwriting” of the processor. Maranzo can be compared to a parquet floor in terms of surface stress.
After completion, any damage to the surface should be repaired promptly to avoid stains.
FRESCOLORI® sealing
Aqueous, satin gloss, transparent and 2-component sealant with good chemical resistance.
MARROC
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
The hidden treasure – a pearl: with its cool, calm and yet very lively elegance. With an extremely thin smoothness optics, but a powdery-soft feel. Marroc sleekly enhances the surface and creates a dreamy feeling.
FRESCOLORI® Marroc
Material: 2 CM3 layers
Wax
Consumption: CM3 about 1,0 kg/m² each layer
Wax, about 0,06 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 3
- Observe the waiting times, with a rest period until the first layer is half dry.
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 3
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Design freedom: light or strong smoothing of the surface
- After short drying, polish with a trowel
- Carefully sand the corners and edges the next day
- Apply the wax with a trowel
- Polish the surface with a polishing machine, provided with a lambskin covered disk, and sand after a waiting period of approx. 1 hour
MATT
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A lightweight, delicate surface with a fine natural radiance – a valued companion of timeless elegance.
FRESCOLORI® Matt
Material: 2 CM3 layers
Consumption: CM3 about 1.0 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 3
- Observe the waiting times, with a rest period until the first layer is dry.
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 3
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Smoothing the surface
- Observe the uniform distribution of the effluent limestone milk
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water
- Instant smooth the surface with a trowel, by applying a uniform pressure
METAL
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A wall design with a fine light structure combined with a metallic surface. The surface of the light is reflected by the glossy surface.
FRESCOLORI® Metal
Material: 2 CM5 layers
2 Sealer-Gel Metal layers
Consumption: CM5 about 1,8 kg/m² each layer
Sealer Gel Metal about 0.4 kg/m² per layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, coverage application
- Observe the waiting times, with a rest period until the first layer is dry.
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 5, somewhat slightly structured
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Design freedom: light or strong smoothing of the surface
- Observe the waiting times, with a rest period until the second layer is dry
- Spread the sealer gel with metal pigments (1-2 times)
- Observe the waiting time of 1 hour
- Spread the sealer gel with metal pigments
- Observe the waiting times, until the sealer gel is dry
- Polish the surface with a polishing machine provided with a felt covered disc
- Einhalten Wartezeit von 1 Stunde
- Aufspachteln Sealer-Gel mit Metall-Pigmenten
- Einhalten Wartezeit bis Sealer-Gel trocken ist
- Oberfläche mit Poliermaschine, Aufsatz Filzscheibe, polieren
PURAMENTE®
Preparation of lime-cement plaster, Aquapanel, etc.
Install stainless steel termination rails with a special adhesive and separately reinforce the inner edge.
Sealing the corners
Finish edges with sealing compound and sealing tape.
Reinforce and seal the wall surfaces with sealing compound
Apply two spatula spreads with a smoothing consistency, with a dry film thickness of at least 2 mm. Apply the sealing compound with the notched trowel, embed in a fabric towel, and press it using a spatula. After drying, retouch the surface a second time with the sealing compound.
FRESCOLORI® pre-applied layer of plaster
Apply the FRESCOLORI® CARAMOR® lime-marble plaster on the previously primed surfaces, in the consistency of the exact grant size.
FRESCOLORI® Puramente
Preparation of floor tiles
Clean the floor tiles with a thinner. Install stainless steel termination rails with a special adhesive and separately reinforce the inner edge.
Sealing the corners
Finish edges with sealing compound and sealing tape.
Reinforce and seal the wall surfaces with sealing compound
Apply two spatula spreads with a smoothing consistency, with a dry film thickness of at least 2 mm. Apply the sealing compound with the notched trowel, embed in a fabric towel, and press it using a spatula. After drying, retouch the surface a second time with the sealing compound.
FRESCOLORI® Puramente design
FRESCOLORI® Puramente
FRESCOLORI® pre-plaster levelling
Pre-plaster FRESCOLORI® Puramente onto the prepared wall surfaces. After drying, apply an intermediate coat of EP Primer. After drying again, apply the next layer and design. With the Puramente surface, waves and slight differences in colour are a characteristic and an idea; these are part of the appearance of the wall design. A special feature of the technique is that the surface does not always have the same structure. Deviations from the sample surface are possible and are the respective “handwriting” of the applicator. After completion, damage to the surface should be repaired promptly to avoid stains.
FRESCOLORI® sealing
Aqueous, satin gloss, transparent and 2-component sealant with good chemical resistance.
PURE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Noble and impervious, like a mirror. A world of splendour Seen from close up, the last structures dissolve – as if the view slips into the depths. A unapproachably smooth surface, which still longs to be touched.
FRESCOLORI® Pure
Material: 1 CM5 layer
1 CM3 layer
Wax soap
Consumption: CM5 about 0.9 kg/m² each layer
CM3 about 0.5 kg/m² each layer
Wax soap, about 0.06 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 5,. Uniform application strictly observed
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 3
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Design freedom: light or strong smoothing of the surface
- Observe the uniform distribution of the effluent limestone milk
- After short drying, polish with a trowel
- Carefully sand the corners and edges the next day
- Apply the wax with a trowel
- Polish the surface with a polishing machine, provided with a lambskin covered disk, and sand after a waiting period of approx. 1 hour
RUSE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Warm, natural and structured – our surface Ruse. The calm and soft surface gives a gentle feeling of comfort.
FRESCOLORI® Ruse
Material: 1 CM7 layer
1 CM0 layer
Consumption: CM7 about 1.5 kg/m² each layer
CM0 about 0.2 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7r
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 0, in tighter execution in all directions
- Observe a shorter wait period
- Polish the surface with a trowel
ROCK
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A differently raised, large-area structured surface – powerful and massive. With the natural radiance of a rocky terrain.
FRESCOLORI® Rock
Material: 1 CM7 layer
Wax
Consumption: CM7 about 1.5 kg/m² each layer
Wax, about 0.11 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Apply the CARAMOR® limestone-marble plaster in grain thickness 7
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Smooth the surface with a trowel
- Pulling the material upwards (suction effect)
- Respect the waiting times with a rest period until the next day
- Easily grind corners and edges
- Apply the wax with a trowel
- Apply instant removal of excess wax with rags
- sofortige Entfernung überschüssigen Wachses mit Lappen
- Einhalten Wartezeit von ca. 3 Stunden
- Oberfläche mit Poliermaschine, Aufsatz Lammfellscheibe, polieren
SCRAPE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Hand-drawn longitudinal lines characterize the appearance of this surface and give it a harmonious appearance. Matte and glossy lines alternate playfully. The surface scrape combines vitality and tranquillity in a coherent manner.
FRESCOLORI® Scrape
Material: 3 CM1 layers
1 CM1.5 layer
2 wax layers
Consumption: 1. CM1 layer, about 0.2 kg/m²
2. CM1,5 layer, about 0.8 kg/m²
3. CM1 layer, about 0.12 kg/m²
4. CM1 layer, about 0.12 kg/m²
5. CM1 layer, about 0.12 kg/m
Wax, about 0.08 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, coverage application
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 1.5, thick and textured with wallpaper wipers
- Observe the waiting times, with a rest period until the second layer is dry
- Application of the third layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, filling in the structural direction
- Observe the waiting times, with a rest period until the third layer is dry
- Application of the fourth layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, filling in the structural direction
- Observe the quite short waiting time (less than touch dry)
- Application of the fifth layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, filling in the structural direction
- Polish the surface with a trowel
- Observe the waiting times, with a rest period until the fifth layer is dry
- Carefully sand the corners and edges the next day
- Apply the first layer of wax with a trowel
- Apply the second layer of wax, if necessary, with a cotton cloth
- Polish the surface with a polishing machine provided with a lambskin covered disc
SMOOTH
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A wall design with sensuality and timeless elegance, caused by a smooth surface design – airy light.
FRESCOLORI® Smooth
Material: 2 CM3K layers
Wax
Consumption: CM3 about 1.2 kg/m² each layer
Wax, about 0.06 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 3, with added grain
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 3, with blended grain
- Humidify the surface with a long bristle brush with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- On the following day, sand the surface (grain size 180)
- Apply the wax with a trowel
- Polish the surface with a polishing machine, provided with a lambskin covered disk, and sand after a waiting period of approx. 1 hour
SPATULA
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
Spatula – Our lively gem! The fine-grained CARAMOR® limestone-marble plaster is applied to this surface in a high gloss aspect. The light reflects on the smooth surface and makes it appear subtle and delicate. The aliveness is obtained by the final staining of the last CARAMOR® layer (application in spots).
FRESCOLORI® Spatula
Material: 3 CM1 layers
1-2 layers of wax (depending on the shade)
Consumption: CM1 about 0.8 kg/m² each layer
Wax about 0.06 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, coverage application
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, a somewhat tighter application
- Observe the quite short waiting time (surface drying)
- Application of the third layer of the CARAMOR® limestone-marble plaster, in grain thickness 1, application in spots
- Carefully sand the corners and edges the next day
- Apply the wax with a trowel
- Observe the waiting times, with a rest period until the wax is dry
- Apply the second layer of the wax, if necessary with a cotton rag
- Polish the surface with a polishing machine provided with a lambskin covered disc
STONE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A fascination in stone – matte and puristic, concentrated on the essentials: the expression of an aesthetic lifestyle, a natural atmosphere and a striking spatial effect. What else could better provide for a similar sensory experience of protection and security?
FRESCOLORI® Stone
Material: 1 CM7 layer
1 CM7G layer
ETC
Consumption: CM7 about 1.2 kg/m² each layer
CM7G about 1.8 kg/m² each layer
ETC, about 0.08 kg/m²
Colour: freely selectable
Application: Indoor
Oberflächen sind vorbereitet und grundiert.
- Auftragen der ersten Lage des CARAMOR®-Kalkmarmorputzes in Kornstärke 7
- Einhalten Wartezeit bis erste Lage trocken ist
- Auftragen der zweiten Lage des CARAMOR®-Kalkmarmorputzes in Kornstärke 7 mit beigefügtem Glimmer
- Einhalten kurzer Wartezeit (handtrocken)
- Oberfläche mit langborstiger Streichbürste/Sprühflasche mit Wasser vornässen, Wasserläufer verhindern
- sofortige Glättung der Oberfläche mit der Spachtelkelle durch gleichmäßigen Druck
- Beachtung der gleichmäßigen Verteilung der austretenden Kalkmilch
- Einhalten Wartezeit bis zum nächsten Tag
- Oberfläche mit Poliermaschine (Körnung 180)
- Auftragen des ETC Schutzes mit Bürste
- Oberfläche mit Poliermaschine, Aufsatz Lammfellscheibe, polieren
STONE XL
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A fascination in stone – matte and puristic, concentrated on the essentials: the expression of an aesthetic lifestyle, a natural atmosphere and a striking spatial effect. What else could better provide for a similar sensory experience of protection and security? Stone XL – our limestone-marble plaster in combination with additionally added mica effect – for punctual glossy effects.
FRESCOLORI® Stone XL
Material: 1 CM7 layer
1 CM7G layer
ETC
Consumption: CM7 about 1.2 kg/m² each layer
CM7G about 1.8 kg/m² each layer
ETC, about 0,08 kg/m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 7, with added mica
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Respect the waiting times with a rest period until the next day
- Surface with polishing machine (grain size 180)
- Application of the ETC protection with a brush
- Polish the surface with a polishing machine provided with a lambskin covered disc
STRUCTURE SEVEN L
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A matte open-pore surface, which gains expression through our CARAMOR® in grain strength 7 and by a lively application. Densely compressed areas give the surface its character, more or less.
FRESCOLORI® Structure Seven L
Material: 1 CM7 layer
Consumption: CM7 about 1.3 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Apply the CARAMOR® limestone-marble plaster in grain thickness 7
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Freedom of design: Application of the plaster in wild lively optics, with a moving line imprinting the surface image
STRUCTURE FIVE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A natural matte open-pore surface, which gains expression through our Caramor in grain strength 5. Sometimes, densely compressed points become smaller.
FRESCOLORI® Structure Five
Material: 1 CM5 layer
Consumption: CM5 about 0.9 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Apply the CARAMOR® limestone-marble plaster in grain thickness 5
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Smooth the surface with a trowel
STRUCTURE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A wall design with a fine, light structure – smooth and humble. The surface is possible with light to strong smoothing while maintaining the light structure. A puristic charm, with a mineral appeal.
FRESCOLORI® Structure
Material:1 CM7 layer
Consumption: CM7 about 1.2 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Apply the CARAMOR® limestone-marble plaster in grain thickness 7
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the effluent limestone milk
- Design freedom: light or strong smoothing of the surface
TRAVERTINE
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
The open-pored living surface gives this surface its name – travertine. It is sometimes smooth and sometimes roughly condensed – a piece of nature.
A strong expressive surface with open pore optics
FRESCOLORI® Travertine
Material: 1 CM7 layer
1 CM7F layer
Consumption: CM7 about 1.2 kg/m² each layer
CM7F about 1.6 kg/m² each layer
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Observe the waiting times, with a rest period until the first layer is dry
- Application of the second layer of the CARAMOR® limestone-marble plaster, in grain thickness 7 (filled) in the structural direction
- In the drying phase, push the surface twice with the travertine smoothing agents
- Smooth the surface with a trowel
URBAN
Delivery and servicing surfaces exclusively by trained FRESCOLORI® processing specialists, with a long-term guarantee of high quality.
A warming embrace: protective, benevolent, very actual. An unobtrusive and yet imposing presence. A character of full confidence, rumbling and proud of its rough flatness.
FRESCOLORI® Urban
Material: 1 CM7 layer
Wax
Consumption: CM7 about 1.2 kg/m² each layer
Wax, about 0.08 kg / m²
Colour: freely selectable
Application: Indoor
Surfaces are prepared and primed.
- Application of the first layer of the CARAMOR® limestone-marble plaster, in grain thickness 7
- Observe the quite short waiting time (touch dry)
- Humidify the surface with a long bristle brush/spray bottle with water, and prevent any running of the water on the surface
- Instant smooth the surface with a trowel, by applying a uniform pressure
- Observe the uniform distribution of the exiting limestone milk
- Design freedom: light or strong smoothing of the surface
- On the following day, sand the surface (grain size 180)
- Apply the wax with a trowel
- Polish the surface with a polishing machine, provided with a lambskin covered disc, and sand after a waiting period of approx. 3 hours
Visit us on
–
